Edge-lighting Sloped Ceiling Surface Mount Magnetic Transformers Manuel d'utilisateur télécharger pdf

MT-600-D12-SL-_

Installation Instructions for Monorail 6

120 Volt Input to 12 Volt Dual

Feed Output

00 Watt Sloped Surface

Mount Magnetic Transformer

904-MT-600-D12-SL-04

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- Do not install this lighting system in a damp or wet

location.

- Do not conceal or extend bus bar conductor through

building wall.

- To reduce the risk of fire and burns, do not install this

lighting system where the insulated open bus bar

conductors can be shorted or contact any conductive

materials.

- To reduce the risk of the system overheating and possibly

causing a fire, make sure all the connections are tight.

- Do not install fixture assemblies closer than six inches, or

as specified in the fixture installation instructions, to

curtains or similarly combustible materials.

- Turn the electrical power off before modifying the lighting

system in any way.

- The fixtures used with the Edge Lighting systems must be

identified for use with the corresponding Edge Lighting

systems.

- Minimum volume of the electrical box must be 6 cubic

inches (98 cubic centimeters).

- The system is "ETL" listed for USA and Canada only when

all the products used are supplied by Edge Lighting.

- RISK OF FIRE: This product must be installed by a

qualified electrician. Turn the power to the electrical box off

during installation. Read the "Important Safety Instructions"

before installation.

- This product is suitable only for indoor dry locations and

approved for the use at any height above the finished floor.

- This product contains a magnetic transformer with a built-in

dimming coil.

- This product may be dimmed only with a low voltage

magnetic dimmer. Using a dimmer other than specified may

work initially, but will eventually cause transformer failure

and void the warranty. The dimmer must be derated as

indicated by the dimmer manufacturer.

- A typical installation is shown. Specific installation must be

in accordance with the local electrical codes.

- Load each circuit of the surface transformer to MAXIMUM

300 Watt.

GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS

PATENT PENDING

1 2 3 4 5

Résumé du contenu

Page 1 - Mount Magnetic Transformer

MT-600-D12-SL-_Installation Instructions for Monorail 6120 Volt Input to 12 Volt Dual Feed Output00 Watt Sloped Surface Mount Magnetic Transformer 190

Page 2

2Install the Surface Mount Transformer4: Connect the provided white and black extension wires to the neutral and hot power wires respectively with

Page 3 - Transformer

310: Connect the white transformer wire to the white extension wire with a wire nut.11: Connect the black transformer wire to the black extensio

Page 4 - 3/8-24 SETSCREW

13 13ONE MONORAIL SECTIONK 8: Place the other Monorail section into the opposite standoff housings. 9: While supporting this Monorail section,

Page 5

POWER FEED ROD2M3 SET SCREW1.5MM ALLEN WRENCH5P1: Remove the wire nuts from the center wires.2: Loosen (DO NOT REMOVE) the bottom M3 set screw on

Commentaires sur ces manuels

Pas de commentaire

Edge-lighting Sloped Ceiling Surface Mount Magnetic Transformers Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Edge-lighting Sloped Ceiling Surface Mount Magnetic Transformers. Edge Lighting Sloped Ceiling Surface Mount Magnetic Transformers User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Edge-lighting Sloped Ceiling Surface Mount Magnetic Transformers